![]() ![]() If motor does not turn it isdefective and the drive assembly must + INSIDE12 VDCP ower Supply15 AMPB reakerRed +Black-FIG. Apply DC volt-age directly to the motor wire minimum of VDC is required to op-erate the motor. Make sure connec-tion is tight and corrosion Disconnect the motor from the hardwareconnection. If wire is defec-tive replace with new Motor Connection & awning motor is connected to thehardware at the top of the awning hard-ware front channel. Arm As-sembly (WeatherPro) and Awning Motor (Oa-sis Elite)A Red and Black Wire (WeatherPro) Red/Whiteand Blue wire (Oasis Elite) of adequate size mustbe run between the control box and the avoid voltage drop follow the chart below todetermining the proper size wire to be LengthWire Size10' & Under14 Gauge11' to 30'12 GaugeOver 30'10 GaugeEXTENDRETRACTA wningControlFUSE INSIDEW eatherProMain ArmRight SidePig Tail toControl Bo圎ndPig Tailfor MotorOasis EliteMotorBlackRedRedBlackRed/WhiteBlueB lackRedBlueRedFIG.ĥ Wire Inside Hardware Channel (WeatherPro Only)To make the connection between the wire run and the awning motor there is a cable run inthe hardware from the bottom to the top. If voltage is below ,check voltage at supply, If OK it may benecessary to increase the wire size goingto the control box. Checkvoltage output on the Red and Black wireat the control box. To ensure proper operation, the controlbox must have a minimum of VDC atthe control box during operation. Thisneeds to be on a separate 15 amp FIG. It is recommended that these wiresbe RED+ and Black 12 gauge wires. Awning InoperableSection Fabric, Roller Tube, Torsion AssemblySection Weathershield Replacement(WeatherPro Only)4 SECTION 1 Supply The 12 VDC supply wire must be run fromthe 12 VDC supply source to the ControlBox. Emergency Close Awning1.Ĥ No 12 VDC AvailableSection (WeatherPro Only)2. No 12 VDC in RVSection (WeatherPro Only)11. Wind SensorSection Auxiliary Close/Open awning1. Wind Sensor WiringSection (WeatherPro Only)2. Wind Sensor Switch OffSection Wind Sensor WiringSection & Wind SensorSection Beeping sound coming from control box1. ![]() Circuit Board WiringSection Awning does not close during high wind1. Wiring/ConnectionsSection & should or visa versa2. Wiring/ConnectionsSection Circuit Board WiringSection & SwitchSection & WeatherPro awning works when Oasis1. Circuit BoardSection Awning works in opposite direction1. SwitchSection Awning will open when ignition key is on position (WeatherPro Only)2. Key FOB BatterySection Key FOB ProgrammingSection Awning works with key FOB but not1.ģ Circuit Board WiringSection & switch (WeatherPro Only)2. DistanceSection not key FOB (WeatherPro Only)2. 12 VDC Supply WireSection FuseSection Wiring/ConnectionsSection, ,, , & Circuit Board WiringSection MotorSection Awning works with remote switch1. 12 VDC Supply WireSection FuseSection Ignition Interlock (WeatherPro)Section & Wiring/ConnectionsSection, ,, & Wind (WeatherPro)Section & Circuit Board WiringSection MotorSection Awning will not close1. Removal.Ģ Hand Torsion Hand Drive Assembly Removal. 8-9 SECTION 8- WeatherPro Fabric, Roller Tube, Torsion Assembly& Weathershield Replacement. 8 SECTION 7- WeatherPro Emergency Retract Retract Procedure. Supply From Control Box To Inside Hardware Channel (WeatherPro Only). ![]() 11/02 2002 Dometic CorporationLaGrange, IN 467612 ContentsPAGE & Oasis Elite 3 SECTION 1- Wiring. ![]()
0 Comments
Leave a Reply. |